Posts Tagged ‘Peak’

New Digidesign Audio Setup in ST4 and ST5

Written by jeff on . Posted in How To, Installations No Comments

With the installation of the new iMacs, I ran into trouble keeping both the MOTU 828mkII and the Digidesign 003 happy. So, the solution for now is to only use the Digidesign 003. The MOTU firewire is not connected.

General troubleshooting note: After you load a program and select Digidesign HW as your audio driver, the Digidesign 003 should respond by saying it is “working..” and the HOST 1394 light, to the right of the display, will be lit.

NOTE: Be sure to patch (on the patchbay) the Digidesign 003 Line Outputs to the Mackie Line Inputs. Otherwise, you will hear nothing.

NOTE #2: When all else fails, switch audio to built in and listen through the computer speakers or your headphones.

For Digidesign Pro Tools:

  1. Just lauch the program. The 003 must be present to open Pro Tools. If Pro Tools can’t find the 003 or can’t establish communications, then quit Pro Tools, turn off the 003, wait a couple of seconds, turn on the 003 and re-launch Pro Tools.

For Digital Performer:

  1. Under the “Setup” menu, check to see if your “Audio System” is set to “MOTU Audio System”
    dp_audiosystem_menu
  2. Then open Setup> Configure Audio System> Configure Hardware Driver
    dp_configurehwdriver
  3. Select Digidesign HW (003)
    dp_select-digi-dw
  4. press OK
  5. You’ll see the Digidesign CoreAudio Manager load as shown in the dock.
    digi_coreaudioman
  6. When you quit Digital Performer, the Digidesign CoreAudio Manager will quit automatically.

For Max 5:

  1. Check audio driver.  Options>DSP Status…
    max_options_menu1
  2. Select CoreAudio Digidesign HW (003) as the Driver.  The Input Device will automatically switch.
    max_dsp-status

For Peak Pro 6:

  1. Go to Audio Menu and select “Audio I/O…”
    peak_audiomenu
  2. Select Digidesign HW (003)
    peak_selectaudiodevice

For Kontakt 3:

  1. Go to the “Setup” menu and select “Audio and MIDI Settings”
  2. Select Digidesign HW (003) as the output driver

For Reason 4:

  1. Go to the Reason menu and select “Preferences”
  2. In the top drop down menu (says “General”), click on it and select “Audio”
  3. Select Digidesign HW (003) in the Audio Output drop down menu. Once the Digidesign CoreAudio Manager loads, Reason will put a green check mark next to the drop down menu.

For Tassman 4:

  1. Go to the Tassman 4 menu and select Preferences then Audio Settings…
  2. Select Digidesign HW (003) in the Audio Settings dialog. Press OK.

Continue Reading ...

Errors in Peak. Error -43 and Error -1

Written by jeff on . Posted in Fixes No Comments

Problem: You open up the recording dialog and press record.  You get this Macintosh Error -43 message.

peak-43

Followed by this Macintosh Error -1 when you close the record dialog box.

peak-11

Solution: You need to check your scratch disc settings.

  1. go to Peak’s preferences and click on the Scratch Discs… button.
  2. peak_prefs
  3. Click on the check box under folder… This un-checks the box.  Then re-check the box under folder…  This will allow you to choose a new folder location.
  4. peak_scratch_folder_check
  5. Choose a folder.  I normally choose the documents folder but you can choose any folder in which you have permission to read and write.  If you want to choose the desktop be sure to choose the one with the colorful icon (it mimics the current desktop). After selecting a place, click Open button.
  6. peak_choose-documents
  7. Back in the Scratch disc dialog box, click OK.
  8. Back in the Preferences dialog box, click Save Preferences Now.
  9. Off you go. You should be able to record.

Continue Reading ...